The engine can not directly erosion by water

The engine is the heart of the entire vehicle, in the usual care and maintenance, in particular to carry out every part of the engine attentive care. Especially for wet weather in spring, it is not taken lightly. Usually walking in the main road, try to avoid car parts through a large puddle in front, as far as possible to prevent water splashing up directly eroded engines.

This is based on the following aspects: First, usually in the car wash, the engine will not be attention to the basic plate, and if the water splashed on the road in time to go without washing, acid rain in the south a larger surface of the engine will cause some rust and corrosion.

Second is that if too much water splashed on the engine, is likely to cause some of the impact of circuit lines, even when serious short circuit occurs inside the case; Once again, there are often attached to the engine surface water may be its long-term impact, if some parts of the combination does not close, the water may have seeped into the inside.

Good maintenance play an important role in car,but Car Diagnostic Parts are necessary.

 SI-Reset Opel OBD2 Description:
- Plug the Device into the SI-Reset Opel OBD2 socket of the car
- All LED`s will blink and than stay on
- Turn ignition key to enable the board electronic but don`t turn on the motor
- Press the button for the operation you want to perform shortly
- The LED of the choosen operation will light and the other Led`s will be off
- LED`s will perform a light chain which means reset is done

SI-Reset Opel OBD2 Functions:
- Reset Inspection Intervall
- 15.000 km or 1 year
- 15.000 km or 2 years
- 30.000 km or 2 years (LONGLIFE)

SI-Reset Opel OBD2 Support Model:
Opel Astra build after 1998, Zafira build after 1998, Corsa build after 2000

SI-Reset Opel OBD2 Packing List:
Service Intervall Reset Unit with diagnostic connector

Faults in air conditioning refrigerant and refrigeration oil caused by

Refrigerant and refrigerant oil caused by the failure, for many reasons, including lack of refrigerant caused by excessive cooling, caused by too little refrigerant refrigeration insufficient refrigerant and refrigerant oil contains too many impurities, micro-blocking caused by insufficient refrigeration, air conditioning and refrigeration the system has insufficient cooling water caused by infiltration, the system has led to inadequate cooling air and refrigeration oils cause poor cooling is inadequate.

If too much refrigerant, heat slowly. If there are too much in the repair when added oil, also can make the cooling capacity of refrigeration system decline. Maintenance methods: from the drying tank above the liquid mirror observation. If the car air-conditioning in the operation from the liquid mirror do not see a bit of air compressor is stopped, no bubble, it is certainly too much refrigerant.

If the refrigerant oil added too much, air conditioning system in normal operation, can see more turbid air bubbles from the liquid mirror. If it is too much refrigerant, can be in the low-voltage side air conditioning repair mouth slowly released some.

Everyone has a heart, if the heart stops beating and the life will disappear.Cars are no exception,diagnostic code reader is the heart of the car,therefore, quality is good and bad, directly affects the car's performance and service life.

Serial piasini v4.1 master is full kit of PIASINI and master version,it include all function in list of the following it can read all dump of chip by bin file.and you can write or edit this dump by yourself.

Serial suite Piasini engineering v4.1 Features:
• JTAG – BDM – K-line – L-line – RS232 – CAN-bus
• read/write programmer
• Windows 2000/XP.
• Checksum correction incorporated for
• Mitsubishi/Denso/Hitachi/
• Server on-line updates and security survey
• New Ecus implementation free of charge

Supported Cars list:
• Denso-Mitsubishi
• Denso-Nissan
• Denso-Suzuki
• Denso-Jaguar
• Hitachi-Nissan
• Keihi-Honda
• EFI-Lotus
• EFI-Lamborghini

Serial suite Piasini engineering v4.1 Supported Motorcycles list:
• Denso-Suzuki
• Denso-kawasaki
• Mitsubishi-Yamaha
• Keihi-Honda
• Simens-Renault
• Denso-Subaru
• Mitsubishi
• Mitsubishi-Mazda
• Denso-Volvo
• Denso-Mazda
• Denso-Reanault
• Transtron
• Denso-Opel
• Mitsubishi-Opel
• Toolbox Serial
• Toolbox C16x

Automotive hanging has abnormal sound

First, the car driving on a flat road certain mileage, so the rear axle temperature rose to normal, and then when the vehicle makes strange noises, write down the speed, parking, set the transmission in the neutral position, and then slowly accelerate until the engine speed and vehicle speed when quite abnormal sound, observe the occurrence of any abnormal sound can be repeated several times in order to determine whether the abnormal sound of the exhaust or engine caused by the abnormal condition.

Rear axle tire noise and noise distinction: with road and tire noise is changed, rear axle noise is not. When the vehicle speed is below 48km / h, the rear axle noise disappears, and the tire noise will continue to exist. When the car is moving and sliding the tire noise is the same, but the noise of the rear axle are different.

Distinguish the rear axle gear noise: In normal straight running, because the differential side gears and planetary gears is almost no relative movement, so hear noise. Cars with the process, the rear axle gear causes abnormal sound occurs mostly caused by poor lubrication, resulting in scar reducer gears grind, if taxiing speeds in a variety of abnormal sound can be heard, then by the reducer drive gear caused by loosening the nut.

Summer is coming, as motorists, we can drive the car to the beach Sun sunbathing,can go to a mountain top,also can go to a strange city adventure to experience different local conditions and customs.These are on our car air conditioning in good condition, otherwise our car is a "mobile oven".So we need to choose good Car Diagnostic Parts to make the car more better.

JP701 Scanner Description:
MaxScan JP701 code scanner is specially designed for technicians to troubleshoot Major Japanese Vehicle Systems. JP701 supports all 9 tst modes of the latest J-1979 OBD2 test specs and used for Reads Engine, Transmission, ABS & Airbag Systems for major Japanese vehicles.
The MaxiDiag JP701 is an innovative multi-functional scan tool designed for technicians to troubleshoot engine, transmission, ABS & airbag systems for major Japanese vehicles. Reliable, easy-to-use & affordable, the MaxiDiag JP701 is a time saver & a money maker.
Global OBD2 - EOBD coverage.

Maxiscan JP701 Vehicle Coverage:
Toyota 1996 - 2008
Honda 1996 - 2008
Mazda 1996 - 2008
Nissan 1996 - 2008
Mitsubishi 1996 - 2008
Global OBD II compliant US, European & Asian vehicles.

Maxiscan JP701 Scanner Functions:
- Retrieves generic { PO, P2, P3 & UO} and manufacturer specific {P1, P3 & U1 } codes.
- Displays DTC definitions on-screen.
- Views FREEZE FRAME Data.
- Displays O2 Sensor Data as well as LIVE Datastream  parameters.
- Data Graphing, 1996 and newer.
- Reads stores and play back of LIVE Sensor data.
- Memory/ Battery backup for off vehicle data review and analysis.
- Performs Modules Present test.
- Retrieves Vehicle Information. {VIN, CID & CVN }.
- Supports all current OBD2 Protocols, including CAN { Controller Area Network }.
- Easy and reliable to use.
- Built in DTC look-up Library.
- Prints data via PC.

Maxiscan JP701 Scanner Packing List:
- User's Manual
- OBD2 cable 1.5V battery X 4
- Nylon carry case

Car requires repeated ignition that can start

There may be because the battery voltage is low as a result of, because sometimes even headlights and other electrical devices have power, but the engine still does not start, because the engine is started when the current required is large, if the battery power loss, then, Although you can drive the car electronics, but not necessarily be able to drive the starter, it is possible that the performance of the battery power loss.

Probably because the throttle, idle motor and air intake and combustion chambers and other parts caused by excessive carbon deposits. Because inlet coke, too much dirt, the air passage cross-sectional area changes, so that the control unit can not be precisely controlled idling intake air, causing the mixture is too thick or too thin, causing the engine will not start.

There may be because the electronic control system to maintain constant fuel poor performance, low fuel pressure injection under low temperature conditions cause poor atomization, resulting in difficult to activate. Recommended to turn the key to start the instrument lights lit stalls, wait a while, you can also complete the self-test procedure is the engine, which is also on the whole engine and other electrical devices are beneficial.

Besides,Car and car maintenance is a hot topic among young people.So,how to choose best Car Diagnostic Parts is also popular with people.Here recommend some car scanners.

MB STAR C4 Description
MB STAR C4 is the professional diagnostic equipment for Mer-Bz cars manufactured, it is the replacement of HHT. IBM Compact 4 operates based on the Windows XP system.

MB STAR C4 Function
- 1989~up to now Car, Bus, Truck, Sprint, Smart; (support:W204,W212,W207)
- All electric system Diagnostic; (Do not include flash code);
- Reading out and erasing trouble code; reading the real-time data of sensor and actuator; testing the components of cars; coding and programming.
Character:
- Realizes all the function of official factory Mer-Bz compact 3.
- C4 Multiplexer can connect to factory computer and IBM laptop.
- Complete maintenance data. It could offer full disassembly and assembly circuit diagram, working principle and element place anytime needed. It is the best assistant for maintenance man.

MB STAR C4 Software language
English/Chinese/Deutsch/French/Italian/Korean/Spanish/Portuguese/
Finnish/Danish/Japan/Swedish

Optional Configuration:
- IB M laptop: T30 or any computer with external HDD
- Tool box
- COM connect with the laptop cable
- Hard disk of each language.

MB STAR C4 Package includes
- C4 STAR MULTIPLEXER( Benx VCI)
- 16 PIN OBD II cable (OBD Diagnostic Socket )
- 38 PIN cable (Old Benz Round Socket )
- 14 PIN cable (Sprint. Bus. Truck Round Socket)
- 4 PIN cable (Old Benz Rectangle Socket)
- 19 PIN cable (Computer Communication)

When driving, why the steering wheel play full with abnormal sound?

Common electric power steering system is divided into the hydraulic steering system and steering system. Because the electric power steering system is relatively sophisticated, and not prone to problems, so for the electric power steering system failure, it is recommended to the service station for repairs.

The first glimpse of the principle of hydraulic steering booster system. Hydraulic steering power steering pump drive from the engine to power source power system tape, steering pressure produce booster pump, push the steering mechanism inside the machine, making the steering wheel to operate freely portable.

When the steering wheel is full, the steering mechanism will arrive at the limiting position, at this time if you continue to turn the steering wheel, steering hydraulic power steering system will enable the continued to rise, but to protect the steering pipe booster system not to rupture, the safety valve is arranged in a hydraulic pipeline, high pressure oil through the relief valve fall, the noise is due to the pressure generated by the. But if this operation, will cause the power steering pump or the steering oil pipe damage early.

Cars make our life more and more convenient, but bring some trouble at the same time.However,we will solve it,if we use auto key programmer properly.

SBB V33 Key Programmer Description:
SBB Key Programmer V33 is a new device used as a portable unit for programming keys in immobilizer units on vehicles. Due to its integrated hardware, SBB needs no more than the OBDII cable provided to carry out a wide range of functions.The latest version is V33.

SBB V33 Key Programmer Function:
- Programming new keys
- Reading keys from immobilizer's memory
- Deactivating keys no longer in the car owner's possession
- Operation by means of a menu guided programming
- Sbb programming new remote controls
- Software with full database containing all the most  important vehicle makes
- Silca SBB V33.2 reading keys from immobilizer's memory
- Silca SBB V33.2 deactivating keys no longer in the car owner's possession
- Silca SBB V33.2 operation by means of a menu guided programming
- Silca SBB V33.2 programming new remote controls
- Silca SBB V33.2 software with full database containing all the most important vehicle makes

SBB V33 Key Programmer Supported Languages:
Italian/German/French/English/Spanish/Greek/Portuguese/Turkish/Russian

SBB V33 Key Programmer Packing List:
- 1pc x SBB Main Unit
- 1pc x OBD II cable
- 1pc x RS232 cable
- 1pc x power supply
- 1pc x CD with user manual

Automotive Transmission jump file faults and exclusion

1.Finds a file in the jump file,will change the gear shift lever, and remove transmission cover watch gear meshing, such as good, should check the transmission fork shaft locking mechanism;to promote the transmission fork test location jump gear device by hand, such as poor positioning, remove the speed shifting fork shaft ball and spring inspection, such as the spring is too soft or broken should be replaced. If the transmission fork shaft groove wear too much shall repair or replace;

2.Check the gear meshing, such as gear is not fully engaged, with hand push jump gear gear or gear sets of proper meshing, should check the transmission fork is bent or too much wear, as well as the transmission fork fixed screw is loose, fork end and gear for groove clearance is too large. If the transmission fork bending correction; as a result of the transmission fork lower wear and sliding gear slot excessive looseness should be removed for repair;

3.As the transmission mechanism, and the gear or gear sets and proper meshing, it should check whether the wear tapered gear, such as severe wear should be replaced; check the bearing and shaft wear, such as shaft wear, bearing looseness or transmission shaft along the axial movement, should be removed for repair or replacement;Inspect the synchronizer work situation and, if failure should be repaired or replaced;

Say that buying a car easy, using a car difficult.In the car driven by the economic interests of the market environment, and finally the best price to buy a bed of roses, but also when buying car accessories, maintenance products with demonstrated effect is no exaggerated or even deceived.so how to choose good Auto Equipment is a challenge.

U581 Scanner is for real-time automotive diagnosis based on the OBD 2 & CAN-BUS protocol. It offers Full Feature Scanning including ‘LIVE DATA’. By simply plugging it into your vehicles diagnostic socket, you will be able to Read all Trouble Codes & Definitions related to the “Check Engine Light”, Save & Review results, Reset the trouble light, Monitor & Freeze-Frame Data,and more. Also retrieves the VIN (vehicle identification number) on supported vehicles.

1.LCD Display , 128*64 pixel display with contrast adjustment, Backlit
2.Enter key selects displayed
3.Exit key go back to the previous screens
4.Up/down arrows-moves the selection pointer and scrolls up or down.
5.LEFT/RIGHT arrows-Select responses and moves cursor.
6.OBDII connector cable, connect car and the scan tool

Functions of U581 Scanner:
- Works on all 1996 and newer cars & light trucks that are OBD II compliant (including the VPW, PWM, ISO, KWP2000 and CAN protocols).
- Reads and clears generic and manufacturer specific Diagnostic Trouble Codes (DTCs).
- DTCs definition displayed on the LCD screen, no need to cross-reference with code book.
- Reading Live Data
- Reading Freeze Frame Data.
- Testing I/M Reading Status.
- Reading Vehicle Info VIN (most vehicles built 2000 & up).
- Rescanning Data.

U581 Scanner Specification:
- LCD Display -128x64 pixel display with contrast adjustment, Backlit.
- "ENTER" key for selection of different functions.
- "ESC" key to go back to the previous screen.
- "UP"& "DOWN" arrows to move the selection pointer and scrolls up or down the menu.
- "LEFT"&"RIGHT" keys for selection of responses and move cursor.
- On/Off Power Button for performing software update process.
- OBDII connector cable for connecting scan tool to the vehicle's Data Link Connector "DLC".
- Battery compartment.

U581 Scanner Support system:
Misfire, Fuel System, Comprehensive components (ccm), EGR System, Oxygen sensor, Catalyst, Evaporative, O2 Sensor heater, Secondary air, Heated Catalyst, A/C System and many more.

U581 Scanner Package Including:
1pc x U581 Super CAN OBDII/EOBDII Memo Scanner
1pc x 1500mm length OBDII Connecting Cable
1pc x COM Cable for connecting U581 to PC
1pc x User Manual
1pc x Durable Nylon Storage Case

Some useful information about the car engine and gearbox

In fact, the actual transport process,the real engine with fewer problems, the owner can through routine periodic maintenance to prevent engine problems.Experts suggest that if the conditions can be frequently changed the oil, because the oil viscosity can be changed for a long time.

If the engine wouldn't start because the battery is dead, mostly caused by the weakness and start; start after sudden flameout shiver, is because the solar term door is too dirty, now is the electronic solar term door, computer will prompt problems; the car shaking, may be the result of three factors lead to aging, including machine foot cracking, the nozzle is dirty in a cylinder not working well, and oil product unqualified.

If the manual transmission models, are generally easy to appear problem is noisy.if it is automatic models, is prone to jump stop and a strong sense of frustration, but note that this is not really distinguish between failure problems, or the model itself, due to poor performance, such as some older models shift when the impact is relatively large; for CVT gearbox problems that may arise between the pulley is leaking or slipping; and now more advanced dual-clutch DSG shift boxes, although the transmission speed is very good, but there are also noisy problems.

Master some common sense about car is important,but you need to know how to choose Car Diagnostic Parts .

CARPROG FULL V4.74 (with all Software's activated and all 21 items Adapters)is the newest version of carprog in 2013,more car models than v4.01 , and new added dongle and count reset cable .

Software: Full V4.74 , support  EDC 16 !!

Carprog full was designed with regard to demands of our customers to have universal tool for car radios, odometers, dashboards, immobilizers repair including advanced functions like EEPROM and microcontroller programmer, key transponder programmer.

CARPROG Full V4.74 with full Set+dongle+count reset cable Functions:
1. Make the Universal tool - CARPROG inside have powerful 16-bit MPU and full set of automotive interface drivers. In basic version you will get hardware with extra functions: 12 input/output pins forEEPROM in-circuit programmer, future possibility's to make on the same hardware Microcontroller programmer, Immobiliser Transponder Key programmer with antenna adapter for 125/134 kHz, K-line diagnostic (dashboard odometer programming, immobilizer key programming), CAN line diagnostic,+5V/+12V output, USB, power supply only from USB.

2. Make the Low Cost tool - with CARPROG basic you will receive many extra functions (like car radio code calculator CC1, EEPROM programmer and VAG dashboard's programmer by CAN) and all additional software's you can buy extra according your need.

3. Make it User Friendly - Windows XP software, works without any installations, on all PC, use USB to PC link, all adapters schematics diagrams on-line.

CARPROG developing purposes :
* Make the Universal tool - CARPROG inside have powerful 16-bit MPU and full set of automotiveninterface drivers. In basic version you will get hardware with extra functions: 12 input/output pins for EEPROM in-circuit programmer, future possibility's to make on the same hardware Microcontroller programmer, Immobiliser Transponder Key programmer with antenna adapter for 125/134 kHz, K-line diagnostic (dashboard odometer programming, immobilizer key programming), CAN line diagnostic,+5V/+12V output, USB, power supply only from USB

* Make the Low Cost tool - with CARPROG basic you will receive many extra functions (like car radio code calculator CC1, EEPROM programmer and VAG dashboard's programmer by CAN) and all additional software's you can buy extra according your need

* Make it User Friendly - Windows XP software, works without any installations, on all PC, use USB to PC link, all adapters schematics diagrams on-line.

Carprog Full V4.74 Parts:
1. CarProg Software:
* ECU-OPEL - OPEL login reader from motor hybrid ECU. Works with Bosch ME1.5.5, Siemens SIMTEC71,SIMTEC71.1, Delco Diesel, Delco Multec.
* OPELCAN - Opel ECU by CAN programmer - read/change mileage in EDC16, MT35E, HSFI 2.2 read PIN, reset ECU
* PSG16 - Opel PSG16 diesel pump by OBDII - read/change mileage, read PIN, reset ECU
* OPEC28 - Opel Siemens Simtec ECU Tool Advanced

Attention
1 - NO INTERNET UPDATE (You’d better diconnect computer from Internet)
IF YOU MAKE INTERNET UPDATE .MCU IN INTERFACE WILL DAMAGE!

2 - ONLY USE WHICH SOFWARE I GIVE YOU IN CD
IF YOU USE OTHER SOFTWARE .MCU IN INTERFACE WILL DAMAGE!

Automatic Transmission Oil full user guide

Lubricating oil injected automatic transmission can not only play the role of lubrication and cooling, more important is to transfer power between the engine and gearbox. The working temperature of the lubricating oil is generally 120 degrees Celsius, so the high quality requirements of the oil, and must be kept clean.

We should always check the automatic transmission oil level is normal. Check method of automatic transmission oil and engine oil is not the same, need to preheat the oil to 50 ℃, then the gear lever is in gear after a short stay in the parking structure, then the normal oil dipstick corresponding surface should be located between the highest and lowest lines, such as not enough, the same quality in time to add oil.

In most cases, we remove the automatic gearbox oil bottom screws to miss the old oil and then add new oil change automatic transmission oil, but this only about new oil a small part, but also most of the old oil still left in the gearbox. If you are changing the way to remove oil pan, you can put 70% of the oil, so as to ensure the transmission of health. The oil present a better method is a dynamic change, using a dedicated transmission cleaning equipment, the full cycle of the old oil, drained and then add new oil, so oil change rate as high as 90%.

Choose good oil, can make the car more durable, more motivated. Good oil, especially fully synthetic motor oil in addition to can protect the engine, to lower the number of oil change, also can save fuel costs.So good tools is useful and necessary.However,airbag reset tool is important as oil.

X-200 is a kind of professional hand auto maintenance resetter, including CBS and OIL resetting, tire pressure alarm lamp resetting(by hand),timing belt CBS reset(by hand),OBDII engine diagnosis, brake pad changing of EPB Electronic Brake and other functions for resetting.

X-200 Oil Reset Tool Functions:
1 Oil Reset
2 Tire Pressure Warning Light Reset
3 Timing Belt Light Reset
4 OBD-II Engine Diagnosis
5 EPB Electronic Brake Pad Replacement
6 Throttle Reprogramming

X-200 Oil Reset Tool Features:
1.One click reset for V.W., AUDI. Input the service miles and days directly. No need to input any channel number. It supports all the vehicles till 2012.
2.Support EPB electronic brake pad replacement for V.W. Audi etc
3.Support engine oil, spark plugs, front brake pads, back brake pads, air conditioner, brake liquid,coolant liquid, vehicle checking, etc. reset for BWM. AND the supported BMW models are F01/F02/F03/ F04/F07/F10/F11/F12/F13/F18/F20/F30,etc.
4.Support the lifespan percentage setting of engine oil for Buick, Cadillac etc.
5.Support Mercedes Benz new C Class, E CIass models and Mercedes Benz VITO/VIANO/SPINTER.
6.Support Porsche Cayenne, Panamera till 2012.
7.Support most of Europe, American, Asia and Chinese brands vehicles.
8.Detailed and clear instructions make the operation more easier.
9.Support online updating. Please use large capacity TF card to guarantee the updating
successfully.
10.Morw functions are updating.

X-200 Oil Reset Tool Packing list:
1 pc* X-200 MAIN UNIT
1 pc*OBD II-16
1 pc*MAIN CABLE
1 pc*TF card
1 pc*TF card reader
1 pc*X-200 user's manual
1 pc*Compressed Case